Running a service / Troubleshooting

Troubleshooting

Fix the problems that come up at the media desk, from the messages AutoSermon shows.

No audio, or the wrong microphone

  1. Open Settings → Transcription → Microphone.
  2. Choose the microphone or mixer input under Microphone. If the names are missing, press Test once.
  3. Press Test and speak. The Input level bar should move.
  4. Leave Noise reduction off for a choir: it can cut held notes.

If the transcript shows “Microphone access was denied”, press Request access in the message, or see Settings → Permissions. The recorder has its own microphone choices in Settings → Recorder.

The speech engine will not install or start

When transcription cannot start, the transcript shows why, with Try again and Transcription settings.

  • “… is not installed. Install it in Settings → Transcription.”: press Install beside the model.
  • “Could not download …”, “… download was incomplete” or “The speech engine download is damaged”: try again on a steady connection.
  • “The speech engine is missing a file. Reinstall AutoSermon.”: reinstall from autosermon.app. Your library is kept.
  • “The speech engine is not installed.”: this model needs the speech engine. Press Get engine, or Locate engine to choose one already on this computer, or choose another model.
  • “… Using local transcription instead.” (or cloud) means the chosen mode could not start and the other one did.

Transcription is slow or falls behind

“Transcription is falling behind. Skipping audio to catch up.” means the model is too slow for this computer, and some speech is lost.

  • In Settings → Transcription, use the model marked Recommended.
  • Check speed, beside an installed model, says whether it keeps up on this computer. Only just keeps up here and Too slow here are likely to fall behind during a service.
  • If the page says This engine is outdated and slow, press Update engine.
  • Close other heavy programs, such as video editors and streaming software, or switch Mode to Cloud.
  • “The speech engine keeps stopping”: stop and start transcription to try the engine again.

A verse is not detected or not shown

  • Read the transcript. If the reference was misheard, the microphone or the model is the problem, not detection.
  • Check the Detected panel on the Bible screen. A verse found there but not shown was held back, not missed.
  • Auto live must be on, in the Detected panel. A paraphrase goes up by itself only at or above the percentage beside it (85 by default). An amber Auto button means it is off.
  • A card marked Held back is a chapter heard without its verse; send it yourself.
  • During a Songs item, verses stay off the screens unless the item has its own Auto live choice.
  • The item’s Auto live, in the Timer, may be set to Nothing or leave out Verses.
  • Settings → Bible & AI → General → Auto live sends must include Verses.
  • A verse the followed presentation quotes goes up as that slide instead.

Songs are not followed

  • Songs are only followed while Auto is running. Check the header.
  • An amber Auto button means Auto live is off. Turn it on in the Auto menu.
  • The item’s type must be Songs. Check the tag on its Timer row and change the Type if it is wrong.
  • The song must be in the playlist named under the item’s Songs. With none named, nothing is followed there unless Follow songs outside the session is on, in Settings → Bible & AI → General. Then it must be in the first playlist, in library order, that another item of the service names under Songs, or, if no item names one, the playlist holding an item a Trigger puts up. To be sure, name the playlist on this item.
  • The song must be a song item with its lyrics on slides.
  • If the Auto menu shows Held on, choose Resume order of service to go back to the printed times.

Output is on the wrong screen

  1. Open Settings → Outputs → Screens.
  2. For each screen, set Display to the monitor it belongs on, Pick automatically, or Movable window.
  3. Make sure the screen is Enabled.
  • Output → Choose Display moves the first output to another monitor.
  • In Windows display settings, set the displays to Extend. Duplicated displays count as one screen.
  • “All outputs are switched off” means no screen is enabled. Turn one on in Settings → Outputs.
  • An output whose monitor is unplugged shows Disconnected under Display and opens nowhere else. Plug the monitor back in, or choose another Display.

The web display will not load on a phone

  1. In Settings → Outputs → Web display, turn Web display on (Standard and above) and copy the URL.
  2. Open that address on the phone, exactly as shown, for example http://192.168.1.20:9876/display.
  3. Connect the phone to the same network as the computer, not a guest network or mobile data.
  • The first time the server starts, Windows asks whether to allow AutoSermon on the network. Allow it on private networks. If it was refused, allow AutoSermon in Windows Security → Firewall & network protection → Allow an app through firewall. On a Mac with the firewall on, allow incoming connections when asked.
  • “Port … is already in use”: choose another Server port in Settings → Network, press Start server and use the new URL.
  • A black page means nothing is live, or the screen it mirrors is off. Change Mirrors to pick the screen.
  • The web display needs no PIN. The PINs in Settings → Network are for the phone pages.

A schedule will not load from another computer

From network…, under Load schedule ▾ → Load schedule on the Timer screen, reads the schedule another AutoSermon computer has loaded.

  • “No other AutoSermon computers found on this network”: press Start server on the other computer in Settings → Network, and connect both computers to the same network.
  • “… does not share its schedule with this computer”: on that computer, add the address the message names under Settings → Network → Network sync → Peers.
  • “… did not answer”: check that the other computer is on and its local server is running.
  • Without a network, use Load schedule ▾ → Export schedule… on one computer and From file… on the other.

Camera or microphone blocked on a Mac

  1. Open Settings → Permissions and press Request beside Microphone or Camera.
  2. If it says Denied, open System Settings → Privacy & Security → Microphone (or Camera) and turn on AutoSermon.
  3. Quit and reopen AutoSermon, then press Re-check.

On Windows, Request opens Windows privacy settings. Turn on access for the microphone or camera, and let desktop apps use it.

A recording is empty

“The video recording is empty. Check the selected device.” means no picture or sound reached the file, and no file was kept.

  • Close other programs that may hold the camera, such as video calls.
  • Check permission in Settings → Permissions.
  • Reconnect the device, right-click the Recorder screen and choose Refresh devices.
  • Pick the camera and microphone by name instead of the default.
  • Make a short test take before the service.

Update problems

  • “Could not check for updates” or “Could not download the update”: check the internet connection, then press Try again in What’s new or Check now in Settings → Version.
  • “Updates are not available for this installation”: download and install the current version from autosermon.app.

Logs and reporting a problem

Help → Open Log Folder shows AutoSermon’s logs. The main log is main.log.

Help → Report an Issue opens the contact page. Include main.log and the time the problem happened.